These products are requested only from ZSE. Our employees will contact you as soon as possible with an offer.
Order on request
This product is ordered on request! An account at myZSE gives you the opportunity to order this product directly.
The new panel mount Instrumentation Amplifier WGA-910A by KYOWA features a 3.5" color LCD graphic display for wave forms and digital readings. It measures strain-gages and strain gage based transducers 4000 times per second with an resolution of 24 bits. The measured data is scaled and presented on the touch-panel-display. A selectable filter smoothes the curve if needed. The data is available on an analog monitor output, a serial interface or can be saved on a SD-Card for further analysis. Programmable alarms can detect abnormal conditions and switch digital output lines.
Features:
The measurement waveform can be displayed.
Touch-sensitive 3.5-inch TFT LCD ensures easy operation and monitoring.
The measurement waveform can be recorded (optional SD card is necessary).
Characters are large and easy to see.
TEDS compatibility for TEDS-based automatic calibration.
5 Comparator Settings: extra high (HH), high (HI), OK, low (LO), extra low (LL).
Comparison value, hysteresis band, comparator output logic and using comparator can be set.
Interfaces : Compatible with IEEE1451.4 Mixed Mode Transducer Interface Class 2 Applicable Transducers : Should have the information according to IEEE template No. 33. Cable length should be 30 m or less
Measuring Range
±3.2 mV/V (Input range includes zero adjustment range)
Bridge Excitation
2, 10 VDCI
Non linearity
Within ±(0.02 %FS+1 digit) % FS
Power Supply
100 – 240 VI
Operating Temperature
-10 – 40 °C
Operating Humidity
20 – 80 % RHI
Dimensions
100x 135 x 96 mmI
Weight
950 g
Standard Accessories
CD-ROM including instruction manual and software for SD card
BCD data : 20 bits(4 bit ×5 digit) Binary data : 18 bits (offset binary) Minus code : 1 bit Over : 1 bit End Of Conversion(EOC) : 1 bit Output format : Open-collector Capacity : 30 VDC, 20 mA (load resistance)
Input
Number of point : 2 Detail : Data hold input Negative logic(Hold at “L”) Output prohibit input Negative logic(Prohibition at “L”) Input signal type : Open collector or Non-voltage contact signal Voltage 12 VDC and current 5 mA can be applied
setting-content
Transmission speed : Approx. 16, 32, 64, 125, 250, 500, 1000 times/sec. Polarity logic, EOC logic, Data logic : Negative, Positive Data type : BCD, Binary Changeable BCD classification : Hold Value1, Hold Value2, Measured Value
BCD data : 20 bits(4 bit ×5 digit) Binary data : 18 bits (offset binary) Minus code : 1 bit Over : 1 bit End Of Conversion(EOC) : 1 bit Output format : Open-collector Capacity : 30 VDC, 20mA (load resistance)
Input
Number of point : 2 Detail : Data hold input Negative logic(Hold at “L”) Output prohibit input Negative logic(Prohibition at “L”) Input signal type : Open collector or Non-voltage contact signal Voltage 12 VDC and current 5 mA can be applied
setting-content
Transmission speed : Approx. 16, 32, 64, 125, 250, 500, 1000 times/sec. Polarity logic, EOC logic, Data logic : Negative, Positive Data type : BCD, Binary Changeable BCD classification : Hold Value1, Hold Value2, Measured Value
D/A Output
Output Voltage
+/-10 VI
Current Output
4 – 20 mAI
Non linearity
Within ±0.1 %FS % FS
setting-content
D/A display : Zero disp. (Displayed value when the voltage 0 V is outputted) Full disp. (Displayed value when the voltage 10 V is outputted) D/A classification : Hold Value1, Hold Value2, Measured Value
Cable extension for load cell and Models integration of multiple load cell outputs to a single cable
A junction box is used when connecting a load cell and amplifier using an extension cable, or when connecting cables of multiple load cells, weighing a tank or hopper, to an amplifier using a single cable.
The SJB-C/D are designed for general purposes, for use under non hazardous and explosive environments.
Cable extension for load cell and Models integration of multiple load cell outputs to a single cable
A junction box is used when connecting a load cell and amplifier using an extension cable, or when connecting cables of multiple load cells, weighing a tank or hopper, to an amplifier using a single cable.
The JBS-C is designed for use under hazardous and explosive environments.
Cable Diameter: 10 to 11 mm (Please specify the cable diameter)
KYOWA ELECTRONIC INSTRUMENTS CO, LTD. is a Japanese company that has been covering all core elements of industrial strain measurement technology since 1951.
Your browser is no longer up to date. Please use a modern browser.
Unfortunately, we cannot guarantee Internet Explorer the full functionality of this website. We recommend that you use a modern browser (e.g. Chrome, Firefox, Edge, Safari). Microsoft also advises against using Internet Explorer for security reasons. You can download a new browser here: