SIRIUS-F

DS-UP-DSA

Additionally offers measurements for Industrial Acoustic, Structural Analysis and Machinery Diagnosis.
Industrial Acoustic: Real time narrow band FFT, Real time 1/1, 1/3, 1/12, 1/24 band octave spectrum, Real time A-, B-, C-, D-weighting, Fast- Slow- Impulse-weighting, Leq-Calculation, Sound Level according IEC 60651, 60804, 61672.
Structural Analysis: Measurement of transfer functions (FRF) for SISO, SIMO and MIMO configurations with H1, H2 and Hv algorithm. Excitation can be either an impulse (modal hammer) or continuous. In this case internal function generator (OPT-FGEN) or external generator source might be used. Structure geometry can be created or imported from UNV, online measurements of FRF, coherence, phase and amplitude is possible.
Machinery Diagnostics: Order Analysis, rotational and torsional vibration, waterfall diagram.
Human Body Vibration according to ISO 8041, ISO 2631-1.

DS-CAM-1100m

CMOS Camera B/W
HD resolution 2048x1088
600 fps VGA resolution
300 fps full HD (online compression JPG)
GiGE interface with POE (4W)
SYNC connector
-5...40°C operating,
54x40x92mm, C-mount objective
IP40 (IP67 option)
Aluminum chassis
Incl. Standard C-mount lens
Incl. cable set 3m, SYNC and Ethernet, incl. POE powersupply
Incl. DEWESoft7 driver requires DEWESOFT-PROF license

DS-CAM-640c

CMOS Farb-Kamera, HD Auflösung 1920x1464
200 FPS @ 2048x1536
300 FPS @ 1920x1080
520 FPS @ 800x600
640 FPS @ 640x480
Sensor CMOS, 1/1,8 Zoll, online JPG Kompression, GiGE Interface mit POE, SYNC Verbinder, -10 °C … + 70 °C Betriebsbereich,  C-mount Objektiv Anschluss, Schutzklasse IP40 (IP67 als Option), Aluminum Gehäuse 119 x 60 x 60 mm, inkl. Standard C-mount Objektiv, Kabelset 3 m, SYNC und Ethernet, inkl. POE Versorgungsadapter für 220 VAC, Standard-Stativgewinde an der Unterseite, inkl. DEWESoft Treiber.

DS-BP4i

Battery packs for SIRIUS and SBOX data acquisition systems for stand-alone, in-vehicle or remote test and measurement applications. A clever click mechanism allows the battery to be attached to SIRIUS and/or SBOX instruments.

Features

• reverse polarity protection 
• Exchangeable during operation
• status display 

Technical specifications

Input Voltage Range

12 – 36 V

Output Voltage

24 VI

Output Voltage

12 – 15 VI

Max. power out

250 W

Total capacity (min) at fully charged state

25 Ah

Battery life (min) at max. rated power

1.5 h

Isolation

500 V

General specifications

Operating Temperature

0 – 45 °C

Weight without batteries

1.9 kg

Weight with all batteries

4.5 kg

Single battery weight

0.65 kg

DS-MOUNT1

This mount can be used to mount SIRIUS data acquisition systems and SBOX data processing computers to the wall, floor or any other flat surface.

EtherCAT Sync Junction

ECAT sync junction is used to synchronize acquisition from Dewesoft EtherCAT based data acquisition devices like KRYPTON with USB data acquisition devices like SIRIUS USB and DEWE-43A.

The ECAT sync junction is not required with R1DB/R2DB, R4, R8 or MINITAURs DAQ systems when extended with EtherCAT devices, because the sync junction is already built into the systems.

DS-MOUNT2

General top mount for SIRIUS data acquisition systems and/or SBOX data loggers. Mount can be used to fit small instruments, such as DS-CAN2, or any accessory that needs to be firmly fixed to the DAQ system.

DS-MOUNT3

Top plate with handle and holder for tablet PC with click mechanism. Fits to SIRIUS and MINITAURs data acquisition systems, SBOX data loggers and battery packs.

DS-BP2i

SIRIUS Battery / UPS box
Supports 2x batteries with hot swap functionality
2x LiIon batteries 16,6V/6,6Ah = 96Wh
Total capacity 180Wh, max. output 16V/10A
Status display, including DC/DC converter for 9-36VDC input
Including car adapter 3pin Lemo to open end 3m,
2pin-2pin Sirius cable, 3pin – 3pin SBOX cable

Technical specifications

Input Voltage Range

10 – 36 V

Output Voltage

24 VI

Output Voltage

12 – 15 VI

Max. power out

160 W

Total capacity (min) at fully charged state

12.5 Ah

Battery life (min) at max. rated power

1.5 h

Isolation

500 V

General specifications

Operating Temperature

0 – 45 °C

Weight without batteries

1.6 kg

Weight with all batteries

2.9 kg

Single battery weight

0.65 kg

DS-MOUNT2K

Top mounting plate for binding KRYPTON DAQ modules to SIRIUS and MINITAURs data acquisition systems, SBOX data loggers and battery packs that.

DS-MOUNT19

Mounting plate for fitting SIRIUS, MINITAURs data acquisition systems, and SBOX data loggers into a 19˝ rack cabinet. 

EtherCAT Power Junction

ECAT power junction is used to connect any EtherCAT data acquisition device like KRYPTON or SIRIUS with the power supply and standard PC computer with the RJ45 Ethernet port. 

Using Dewesoft processing computers and data loggers like SBOX, KRYPTON CPU, R2DB, R4, R8 or MINITAURs​​​​​​​ do not require this accessory as the power is provided directly from the mentioned units.

DSI-ACC Adapter

Isotron (constant current powered) adapter for IEPE sensors (accelerometers, microphones)
4 mA const. current, 21 V, 1.5 Hz HPF.

DSI-CH-50 Adapter

Charge input adapter for accelerometers or microphones. Range up to 50000 pC, AC coupled with 0.07 Hz, BNC signal connection, max. 100 kHz bandwidth.

DSI-CHG-DC

DSI-Adapter für Messungen mit Ladungssensoren
Er verfügt über vier Eingangsbereiche von 1 kpC bis 500 kpC. Wählen sie zusätzlich zur DC-Messung im Kanal-Setup der Dewesoft X3 Software aus vier verschiedenen Hardware-Hochpassfiltern.

Der große Vorteil des DSI-CHG-DC-Adapters ist eine zeitkonstante, praktisch DC-Ladungsmessung mit einem DC-Drift von weniger als 0,1 pC/s für den Eingangsbereich von 500 kpC.

Die Bandbreite des DSI-CHG-DC beträgt 20 kHz für den 500-kpC-Bereich und 200 kHz für den 50-kpC-Bereich. DSI-CHG-DC wird von allen SIRIUS DAQ-Verstärkern mit DSUB9-Eingangsanschlüssen und  KRYPTON STG-Verstärkern unterstützt. Die Konfiguration des Host-Verstärkers und die Kalibrierdaten können über TEDS ausgelesen werden.

DSI-RTD Adapter

Pt100, Pt200, Pt500 and Pt1000 adapter. 2, 3 and 4 wire connection methods over 5-pin Binder 710 series connector, automatic adapter identification.

DSI-TH Adapter

Thermocouple adapter. High accuracy cold junction reference measurement, 1 m thermo cable with Mini TC connector, automatic adapter identification.
Please specify TC-Type J, K, T or C.

DSI-TH-UNI

Universeller DSI-Adapter zum Anschluss von Thermoelementen an DEWE-43, MINITAUR, Iolite und SIRIUS-STG, -STGM, STGS, -LV.
Unterstützte Thermoelement-Typen: (K, J, T, R, S, N, E, B, C)
Inklusive integrierter Vergleichsstellenkompensation mit einer CJC-Genauigkeit von 0,5 °C.
0,5 m Thermokabel mit Mini TC Buchse.
Automatische Identifikation des Adapters durch den Messverstärker.

DSI-V200 Voltage Adapter

200 Volt input adapter. Differential input configuration over BNC connector, bandwidth and ranges are defined by connected amplifier, automatic adapter identification.

DSI-20mA Adapter

20mA current input adapter with internal shunt 50Ohm, 0.05%, screw terminals in housing for cable fixing. Use for sensors with 0/4…20 mA output. Automatic adapter identification.

DSI-LVDT Adapter

LVDT input interface for DEWE-43A, DS-Minitaur and SIRIUS (9pin).
Generates 4 or 10 kHz excitation forr LVDT-sensors, phase adjustment by potentiometer, output 1 V = 1000 mV/V, automatic adapter identification.

DSI-5A-D9m

5A DSI Adapter with TEDS,
0.1Ohm 0.05% Shunt Resistor
Small Box with 1m cable and DSUB-9 connector and screw terminals
Fits to DEWE-43, Minitaur, SIRIUSi-STG, -STGM, -STGS, -LV

DSIi-10A

DSI adapter for direct current measurement. Isolated “shunt” with 10 A FS and accuracy < 0.5% FS and bananna connector.

DSIi-20A

DSI adapter for direct current measurement. Isolated “shunt” with 20 A FS and accuracy < 0.5% FS and bananna connector.

DS-16xLVDTr

DS-16xLVDTr – Adapter for 16 LVDT Sensors

DS-16xLVDTr uses a unique ratiometric architecture to eliminate several of the disadvantages associated with traditional approaches to LVDT interfacing. DS-16xLVDTr combines 16 channels of DSI-LVDT adapters in a 19”-rack compatible housing with 1U height.

The main advantage of the new design is the asynchronous excitation signal provided from an external function generator to a BNC front connector (IN connector). When using multiple DS-LVDTr devices the EXC signal can be daisy-chained from the BNC OUT connector to the BNC IN connector on the other device.

There are 16 DSUB-9M male connectors on the front panel for the connection to the Dewesoft data acquisition system. Each connector includes a trimmer for phase adjustment.

On the back panel are 16 DSUB-9F (female) connectors for the LVDT sensor connection. DS-16xLVDTr supports measurements with full-bridge and half-bridge LVDT sensor types.