MCF-B – Multi Signal Conditioner
8-/16-channel carrier-wave and DC strain amplifier, voltage, IEPE, thermocouple, frequency
Order on request
These products are requested only from ZSE. Our employees will contact you as soon as possible with an offer.
Order on request
This product is ordered on request!
An account at myZSE gives you the opportunity to order this product directly.
- Simple settings enable to greatly shorten working hour
- 4-digit CAL switch enables to set sensors' sensitivity easily without calculation
- Various type of conditioner cards for different sensors
- Easy binding
Outstanding vibration resistant enables on-vehicle application
Monitor card equipped with a large digital indicator
The Multi Signal Conditioner MCF-B is a portable and moderate price system capable of mounting 8 or 16 conditioner cards. Selection of optimum cards enables economical system configuration to the exact requirements for each individual application.
Easy operation and excellent vibration resistant make it usable conveniently outdoors for up to 16-channel simultaneous measurement of various physical quantities.
System Components:
- MCF-8B Base Unit for measurement of up to 8 channels, incl. Monitor Card DPE-90A-8 and RS-485 control interface
- MCF-16B Base Unit for measurement of up to 16 channels, incl. Monitor Card DPE-90A-16 and RS-485 control interface
- Conditioner Cards:
- DPM-91A/91A-I 5kHz Carrier frequency Conditioner Cards for Strain Measuring
- DPM-92A/92A-I 12kHz Carrier frequency Conditioner Cards for Strain Measuring
- CDV-90A DC-Excitation Conditioner Card for Strain Measuring
- CTA-90A Thermocouple Conditioner Card
- CCA-90A IEPE Amplifier
- CFV-90A Frequency / Voltage Converter
Your search returned no results.
MCF-8B
Grundgerät mit 8 Einschüben und RS-485 Interface
- Spannungsversorgung: 10 bis 30 VDC
- Inkl.: DC-Spannungskabel P-76, Sync-Kabel U-59 und Stecker für den zentralen Ausgang, Ersatzteile, Werkzeug und Handbuch sowie Monitor Card DPE-90A-8.
Request
S
MCF-16B
Grundgerät mit 16 Einschüben und RS-485 Interface
- Spannungsversorgung: 10 bis 30 VDC
- Inkl.: DC-Spannungskabel P-76, Sync-Kabel U-59 und Stecker für den zentralen Ausgang, Ersatzteile, Werkzeug und Handbuch sowie Monitor Card DPE-90A-16.
Request
S
DPM-91A
Carrier frequency amplifier
- Carrier frequency: 5kHz
- Bridge Excitation: 2 Vrms
- Frequency Response: DC to 2,5 kHz
- Programmable 2nd order Butterworth LPF
- Reads the sensor's TEDS information then sets the rated output
- Input connector: NDIS4102 (7 pins) connector
- Output connector: BNC connector, incl. Output cable U-59
Request
S
DPM-91A-I
Carrier frequency amplifier
- Carrier frequency: 5kHz
- Inverter noise reduction circuit
- Bridge Excitation: 2 Vrms
- Frequency Response: DC to 2.5 kHz
- Programmable 2nd order Butterworth LPF
- Reads the sensor's TEDS information then sets the rated output
- Input connector: NDIS4102 (7 pins) connector
- Output connector: BNC connector, incl. Output cable U-59
Request
S
DPM-92A
Carrier frequency amplifier
- Carrier frequency: 12kHz.
- Bridge Excitation: 2 Vrms
- Frequency Response: DC to 5 kHz
- Programmable 2nd order Butterworth LPF
- Reads the sensor's TEDS information then sets the rated output
- Input connector: NDIS4102 (7 pins) connector
- Output connector: BNC connector, incl. Output cable U-59
Request
S
DPM-92A-I
Carrier frequency amplifier
- Carrier frequency: 12kHz
Inverter noise reduction circuit
- Bridge Excitation: 2 Vrms
- Frequency Response: DC to 5 kHz
- Programmable 2nd order Butterworth LPF
- Reads the sensor's TEDS information then sets the rated output
- Input connector: NDIS4102 (7 pins) connector
- Output connector: BNC connector, incl. Output cable U-59
Request
S
CDV-90A
Strain Amplifier
- Bridge Excitation: 2 or 10 VDC, switchable
- Frequency Response: DC to 50 kHz
- Programmable 2nd order Butterworth LPF
- Reads the sensor's TEDS information then sets the rated output
- Input connector: NDIS4102 (7 pins) connector
- Output connector: BNC connector, incl. Output cable U-59
Request
S
CTA-90A
Amplifier for thermocouples
- Thermocouples: K, T, J, N, E, and R
- Frequency Response: DC to 10 Hz
- Input connector: One-touch type terminal block
- Output connector: BNC connector, incl. Output cable U-59
Request
S
CCA-90A
IEPE Amplifier
IEPE Amplifier
Max. ±5000 mV
Charge converter is necessary when using charge output accelerometer.
Sensor Supply: Built-in constant-current supply(4mA)
Excitation voltage Approx.24 VDC
Frequency Response: 0.2 Hz to 50 kHz (Deviation: +1, -3 dB)
Input & output connector: BNC
Request
S
CFV-90A
F/V Converter Card
F/V converter card
Frequency Response: 0.2 Hz to 100 kHz
*When set to 1.0 V output and 20 kHz range, 100 kHz input can measure as 5 V.)
Input Voltage: ±0.5 to ±50 V
Input Coupling: AC or DC
Trigger Level: 0.0 to 5.0 V in 0.1-V steps
Input connector: NDIS4109
Output connector: BNC
Request
S
MCF-DIN
- DIN-RACK Montagesatz.
- Abmessungen 480 x 132,5 x 40 mm
Request
S
D
UEA360-1540
AC adapter for MCF-A & EDX-200A-4H
Request
S
UEA360-1540
AC adapter for MCF-A & EDX-200A-4H
S
D
MCF-DUMMY2
Dummy Card for MCF-8A or MCF-16A
Request
S
MCF-DUMMY2
Dummy Card for MCF-8A or MCF-16A
S
D
MCF-HANDLE
1 pair of handles for MCF series
Request
S
MCF-HANDLE
1 pair of handles for MCF series
For MCF-8A or MCF-16A
S
D
N-137
RS-485 Y-cable for MCF-B
Request
S
N-137
RS-485 Y-cable for MCF-B
9-pin male D-Sub & 9-pin female D-Sub to centralized connector
S
D
N-136
RS-485 extension cable for MCF-B
Request
S
N-136
RS-485 extension cable for MCF-B
9-pin female D-Sub to 9-pin male D-Sub
S
Kyowa Electronic Instruments
KYOWA ELECTRONIC INSTRUMENTS CO, LTD. is a Japanese company that has been covering all core elements of industrial strain measurement technology since 1951.
