LAT-A – 6-component Force Measuring System
(300N; 10 – 20 Nm)
Order on request
These products are requested only from ZSE. Our employees will contact you as soon as possible with an offer.
Order on request
This product is ordered on request!
An account at myZSE gives you the opportunity to order this product directly.
Each system in the LAT-1000A series consists of the LAT-A 6-component force transducer and the FDP-106A signal processor.
The LAT-A simultaneously detects 3 force components in 3 axial directions orthogonal to the transducer and 3 moment components around these 3 axes.
The FDP-106A eliminates interfering components contained in transducer output through calculation. Thus, by minimizing errors due to interference, the system enables highly accurate measurement of both single- and multiple-component force loads.
Features:
- To guarantee measurement accuracy, performance with multiple component force loaded is indicated with a maximum error (see note in the data sheet).
- Highly accurate measurement possible even with multiple component force loaded
- Simultaneous sampling of 6-component force and processing signals up to approximately 300 Hz possible
- The compact, lightweight transducer is strain gage based and is cased with a highly rigid special aluminium alloy.
- Calibration coefficient is preset in the signal processor, enabling immediate measurement by connecting a monitor indicator.
- Force and moment can be read directly on a PC if connected.
- Direct reading mode is provided to read force and moment at the load point.
- High/low limit and hysteresis width of the high/low limit are used to set an alarm output.
Specifications
General
- Safe Overloads
- 120 %
- Nonlinearity
-
±0.5 % RO
- Hysteresis
-
±0.5 % RO
- Interference
-
±0.8 % RO
- resolution-fs
-
0.05 % FS
- Temperature Effect on Zero
-
±0.25 % RO/ºC
- Temperature Effect on Output
-
±0.05 %/°C
- Compensated Temperature Range
-
0 – 50 °C
Communication Program
- OS
-
Windows® 7
- Display
-
800×600 pixel I
- Memory capacity
-
64 MB or more
6-component Force Transducer LAT-A
- Eigenfrequenz
-
Fx, Fy : Approx. 2.3 kHz, Fz: Approx. 5.5 kHz
Mx, My : Approx. 8 kHz, Mz: Approx. 4 kHz
- Recommended excitation voltage
-
2.50 VDC
- Safe Excitation Voltage
-
5 VDC
- Input Resistance
-
58.3 ±10%
- Output Resistance
-
350 ±2%
- Compensated Temperature Range
-
0 – 60 °C
- Safe Temperature Range
-
0 – 70 °C
- Temperature Effect on Zero
-
±0.05 % RO/ºC
- Temperature Effect on Output
-
0.05 %/°C
- Weight
- 250 gI
- Degree of protection
-
IP30
- Cable
-
Cable
Type: N-78
Wires: 14 (0.3 mm2)
Isolation: PVC
Diameter: 9 mm
Connector
Type: PRC04-12A16-14 (Sensor)
Type: 17JE-23150-02 (D8A) (Measuring instrument)
*Shield wire is not connected to the case.
For displacement and angle of inclination, contact us.
Signal Processor FDP-106A
- Non linearity
-
±0.05 % FS
- Calculation Error of Compensating Interference
-
±0.1 % FS
- Analog Output
-
Channels: 6
Output: ±5 V (150% the rated output of 6-component
force transducer may be made ±5 V)
Resolution: 0.05% FS
Frequency response: DC to approx. 300 Hz
Initial setting: ±5V analog output for the rated capacity
of 6-component force transducer, 0 mm for
coordinates X, Y and Z at the load point
- Serial interface
-
RS-232C
Transmission mode: Start-stop synchronized mode
Baud rate: 9600 bps fixed
Data: 8 bits
Parity: None
Stop bit: 1
Transmission contents: Data, setting conditions
Data format: Binary or ASCII
Connector: D-Sub 25 pins, female
PC connection: Optional interface cable for RS-232C
- Stability
-
Zero point ±0.25 μV/V per °C
Sensitivity ±0.01%/°C
- Functions
-
Over input checking, automatic zero balance,
load point correction, alarm
- Input
-
Channels: Max. 6 (6-component force)
Zero balance adjustment: Automatic
Bridge excitation voltage: 2.5 VDC
- Monitor indicator
-
LED
- Sampling Frequency
-
When not using digital output
0.72 ms/6-channel (Cutoff frequency 366 Hz)
When using digital output
22.9 ms/6-channel in binary format (Cutoff frequency 11 Hz)
45.7 ms/6-channel in ASCII format (Cutoff frequency 6 Hz)
- Alarm output
-
Open collector
- Operating humidity
- 95 %I
- Power Supply
-
100 VAC (200 VAC models are also available.)
- Dimensions
-
180x 255 x 88 mmI
- Weight
-
2.50 kg
Your search returned no results.
LAT-1030KA-1
- Rated Capacity
-
Fx, Fy, Fz: 300 N
Mx, My, Mz: 10 N·m
- maximum-error
-
±1.5 % RO
Request
S
LAT-1030KA-2
- Rated Capacity
-
Fx, Fy, Fz 300 N
Mx, My, Mz 20 N·m
- maximum-error
-
±3 % RO
Request
S